Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
They are making a number of great pointers on Installing A Bathtub as a whole in the content below.
Mounting a tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move speedily; if you need to open up a wall to get rid of the old tub and also place the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub and also set in the brand-new one. Make certain you have qualified on your own for the task and fit attempting it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you mount a new tub in your bathroom if you have currently bought a brand-new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist need to comprise the following:
Getting ready for the Installment
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps system to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted gain access to that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub until the level checks out level.
To mount taps, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub needs to wait till the bathtub has been utilized at the very least when as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with dampness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and also cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that article about How to Install a Bathtub Yourself from an acquaintance on another web property. Enjoyed reading our content? Please share it. Let others locate it. I recognize the value of reading our article about How to Install a Bathtub.
Set Up An Appointment Report this page